Skip to content
Sewage overflow or burst main: your water company (Yarra Valley Water 13 27 62)Smell gas: the leak number on your gas bill · Danger: 000
Home / Taps

Taps

How to change a tap washer and fix a leaking tap

Updated 16 October 2026 · 4 min read

Quick answer

A traditional washer tap may drip when its washer wears; mixer and ceramic-disc taps need a different assessment. It is one of the few plumbing jobs Victoria's regulator says a householder can do. Here is how.

About this pageWritten by the Plumbing, Answered editor, checked against the regulator and water company sources listed below on 16 October 2026. Not written by a licensed plumber.

You can do this Regulation 13 permits tap-washer and defined minor tap repairs in a dwelling by an unlicensed or unregistered person. The definition excludes mixer taps and cartridges, ceramic-disc spindles, breeches and outlets, and work on thermostatic mixing, tempering or backflow devices. Identify the fitting before attempting a traditional washer repair.

What you need

A shifting spanner, a flat screwdriver, a new washer (or a washer and jumper valve kit) the right size, and a cloth to protect the chrome.

The steps

  1. Turn off the water at the isolation valve under the sink or at the meter.
  2. Open the tap to drain it.
  3. Remove the handle: prise off the button on top, undo the screw, pull the handle off.
  4. Undo the tap body (the headgear) with the spanner, turning anticlockwise, with a cloth over the chrome.
  5. Swap the washer and jumper valve on the bottom of the headgear.
  6. Reassemble, turn the water back on slowly, and check for drips.
Illustration: a kitchen tap pulled apart on a timber bench: the tap body, a jumper valve, a small rubber washer and a shifting spanner
Illustration of the job, not a real house.

If it still drips

The seat inside the tap may be worn and need re-facing, or the tap is a ceramic disc or mixer type that needs a cartridge rather than a washer. That is a plumber's job: hipages puts small tap repairs at about $80 to $150.

Replacing the whole tap

Fitting a new tap is a job for a licensed plumber. New brass taps are moving to lead-free: Victoria's lead-free requirements apply from 1 May 2026 to installed copper-alloy products in contact with drinking water; check the product's current certification with the plumber. More in is Melbourne tap water safe to drink.

Common questions

Can I change a tap washer myself in Victoria?

Yes. The regulator lists fixing a leaking tap among the small plumbing jobs a householder can do.

How much does it cost to fix a leaking tap?

A few dollars for a washer if you do it yourself; about $80 to $150 for a small tap repair by a plumber, according to hipages.

Identify a traditional washer tap first

The steps above concern a conventional washer tap, not every fitting with a rotating handle. A mixer tap, cartridge or ceramic-disc spindle may need a different repair and falls outside the minor-tap-repair definition described here. If you cannot identify the fitting, ask a licensed plumber rather than buying a washer and opening it to find out.

The location of the leak matters too. Water dripping from the outlet, leaking around the handle or appearing below a basin can involve different components. Observe where it first becomes visible without opening pipework. A wet cabinet does not establish that the tap washer is the cause.

For an invented example, a tap that stops dripping at the outlet but still leaks around the spindle has not been fully repaired. Replacing the same washer repeatedly would not answer the second problem. Stop and obtain an appropriate assessment rather than tightening parts harder.

Before isolating the water

Make sure you know the correct accessible isolation point and can operate it safely. If a valve is seized, damaged or unidentified, do not force it. A water-company meter problem and a fault in private pipework can require different contacts.

Tell other occupants that the supply is being isolated and make sure the work can be completed without leaving the household unexpectedly without water. If you cannot restore a sound fitting or the supply will not stop, arrange help rather than continuing with the tap partly disassembled.

Protect the basin opening so a loose screw or small part cannot fall into the drain. Keep the removed parts in order and choose a replacement suited to the actual fitting. A kit described as universal still needs to match the tap and its instructions.

If the repair needs more than a washer

Stop if parts are corroded, the body will not undo normally, the seat appears damaged or the fitting differs from the expected washer arrangement. Forcing a stuck bonnet or using the surrounding pipe as leverage can turn a small leak into a larger job.

The current definition of minor tap repairs excludes mixer taps and cartridges, ceramic-disc spindles, breeches and outlets, and work on mixing, tempering or backflow devices. The exemption is not permission to replace any component connected to the tap. A whole-tap replacement needs the appropriate practitioner.

After reassembly, check the fitting and the area below it from a safe position. If water appears somewhere new, isolate it where safe and arrange help. Keep the product details and explain what was changed so the plumber does not have to reconstruct the sequence.

Discussing a professional repair

Give the plumber the tap type if known, the location of the leak and any work already attempted. Ask whether the quote includes the call-out, diagnosis, replacement parts and any proposed additional work.

If replacement is recommended, ask why a repair is unsuitable and which product is proposed. The lead-free taps guide explains the Victorian product change; a recommendation still needs to fit the particular installation. This site does not inspect a fitting or decide which repair your home needs.

Sources

  1. Plumbing Regulations 2018, version 010 in force from 1 May 2026, regulation 13 and minor-tap-repair definition, checked 16 October 2026
  2. hipages, How much does a plumber cost? (updated 24 July 2026)
  3. WaterMark (Australian Building Codes Board), Lead free plumbing products

Checked 16 October 2026. Rules and prices change; check with the regulator, your water company or a licensed plumber.

Who do I call?